VETROO AL800 Full Tower PC Computer Case w/Door Opening Design Tempered Glass, E-ATX/ATX Support, Built-in ARGB LED Strip, Pre-Installed ARGB & PWM FDB Fan in Rear, Support for 40 Series GPUs -Green

It pulls a paper towel towards the case from 6 inches away at IDLE SPEED!
I needed a new case for my triple fan radiator. My old case was the same size but only fit a 2 fan radiator at the top. I had a choice between this and a perhaps more appealing to a gamer yet likely cheap materials at a higher price due to it’s aesthetics pc case. I decided to go with this, and went from a black case to this white for the ambiance effect it has with RGBs. But what won me over was the extra fans. I figured I wanted beauty and performance over sleek faux futurism.I regret nothing! I installed 2 ARGB fans into the extra slots immediately, and replaced the fans underneath the GPU as well. Btw, YES they make a difference! My 2080ti runs noticeably cooler when gaming. They 2 under the gpu, the 3 front, and the 2 extras inside are set to INTAKE. Holy cow do they suck in air. The exhaust fan in the back is blowing cold air when it’s running at full. There is only a little heat that comes out of the top radiator. The inside of this case is getting so much fresh air, it’s just ice cold all the time.My old case had 3 fans but only had a narrow slot along the front, and on the bottom to draw in air. This case has the whole front panel to draw in air. Then you got fans along the side helping pull more air, as well as the bottom, and your psu also pulling air.THIS BABY IS A VACUUM… without all the loud noise.Downsides. The extra white fans aren’t anything to brag about.Also the bottom has screws for 3 fans… However it’s impossible to fit a fan in the middle slot with an ATX motherboard. All the case/usb and other wire essentials plug in and stick out. These bulky fans, and my narrower fans both fail to fit. They should have moved the mounting holes just a few millimeters towards the glass and it’d be perfect. Idk how they could have made such a great case. And then fail to notice such a flaw that is so easy to fix at the manufacturers level. I will eventually have to drill my own holes, but honestly I am not that picky. I just have an ugly gap between my fans. I 3d printed an icicle to hold up my gpu there instead.I am going to give this a 5 star solely because that extra fan doesn’t matter, and out of an otherwise perfect case. I can accept one small flaw for it’s price. If it was over $150 in price, I would give it a 4. But this is too good of a case for it’s price for me to give it anything less than a 5.

Well built for the cost 👍👍
I have build many custom computers for years and this case is better built then I expected for the cost. It has a nice hinged glass door and plenty of room on the back side for cable management.Is it the best… no it has its down sides like the case is made out of thin metal and the holes for cable management are not rubber lined or covered so you can see everything through them if you dont clean up you build. But for the cost it is great. It has enough room for a 360 radiator and can even run oush and pull with the fans. The cables have a good sleeving to them so its not just some ugly colored cabkes. Can hold up to eatx boards with still enough room for a front mount radiator. Doesnt have a vertical gpu mount which is very common on higher end cases and the rear pcie covers are not reusable they are stamped and if removed cant be reinstalled which is a down side for future use. Also be careful upon removing the rear pcie covers because of the thin case metal you can really bend the back side slots easily removing them.Has food filtration withiut a lot of restrictions. Also not a large obnoxious emblem that makes the case feel cheap like some more expensive cases do. Its just a very clean well build low costing case.

The argb fan controller works fine but I connect both the fan and argb connectors directly to mobo headers. The two installed lower fans are redundant in my opinion, and I removed these. In fact i would suggest removing them in the first instance to install a full ATX, for full to the mobo headers/ connectors. Although there is USB/C connectors for the case ports, they will not be up to the full speeds required for most users but work as expected. There are all of the screws required for build, provided in a bag, in the case. The case is made of a relatively thin alloy and when screwing in fans, etc. be careful not to overtighten as this could deform the screw holes. The layout is decent and ATX mobo and power supply went in easily enough. There is no PWM direct management for any of the supplied fans, although white 120mm fan replacements do not look out of place. The general space to accommodate various cooling options such as top mounted 360 aio coolers is more than adequate although a decent fan cooler will fit perfectly as well. The airflow through the unit appears fine on temperature testing although I did replace all of the fans for the aforementioned reasons. Power supply is good although easier to remove the disk tray that has a thumbscrew fitting, for easier cable management (replace after cabling if required).Overall, when finished, looks very nice and not out of place for a decent build.

Thin metal. Nice glass. Pink is in.Instructions were thin with zero on the mess of wires and English errors. We bought it because it’s pink period.Bitter disappointment after half a day of assembly.